FTO AUSTRALIA

Don't you people have Micro$oft Office on your friggen PC's?

I'll upload that too if you want!

Yep got them thanks Ben.

Just a few quick questions to someone who has fit them please (KJ? Pleaseeee!) Is it really easy to remove the dial stops? Am I reading the instructions properly thinking I don't need to take the needles off. I've read other dial instructions, am I thinking correctly I should just follow some of these instructions if I need to more the dials?

ooooo.. i see these are comin shortly, is there an ETA for WA or do i just add another 2 - 3 months on top

Bennoz wrote:Don't you people have Micro$oft Office on your friggen PC's?

I'll upload that too if you want!

haha
i said im downloading it now !!

RallyMad wrote:Yep got them thanks Ben.

Just a few quick questions to someone who has fit them please (KJ? Pleaseeee!) Is it really easy to remove the dial stops? Am I reading the instructions properly thinking I don't need to take the needles off. I've read other dial instructions, am I thinking correctly I should just follow some of these instructions if I need to more the dials?

should be no reason to that the needles out which is what I think you are asking.

should we disconect the battery when doing all this wiring or what?
anyw where can i get this 1am inline fuse
wats it look like

Thanks Ben, received the package today.

Just go to any auto store (autobarn etc). and get a inline fuse holder for a glass fuse and get a 1amp glass fuse to fit in it.

Just put mine in, found like KJ that I had to cut the wires as the plugs don't fit through the bulb holders, although am having a few issues now.

Tacho isn't spinning freely, keeps stalling and isn't moving accuratly. Also I forgot to top up the fuel tank first so I'll have to leave the clear cover off until I fill up and then make sure the dial is at full. On top of all that I tested it before I secured everything and all was good but now it isn't getting power so I'll have to pull it out again.

Anybody got any ideas with the Tacho?

Try Pulling the tacho needle out a bit. Use the 2 teaspoon technique

Supplanter wrote:Try Pulling the tacho needle out a bit. Use the 2 teaspoon technique

the problem is that the dials are not stuck down hard enough. its raised enough at the centre to stop the needle moving freely. double sided tape will fix it.

WOOT, i finally got them and they look good.

but i still need a fittment guide, the current one still doesn't work for me.

khunjeng wrote:

Supplanter wrote:Try Pulling the tacho needle out a bit. Use the 2 teaspoon technique

the problem is that the dials are not stuck down hard enough. its raised enough at the centre to stop the needle moving freely. double sided tape will fix it.

Yeah thats what I found in the end, the 1.5mm double sided tape I was using wasn't keeping it down enough, Now I just used some sticky tape doubled over on itself and works sweet

Oh and heres another tip, don't let your bored father help with the wiring, took me another hour to fix the part he dodged up

I was going to do a DIY with some pics maggsy but after the issues I had you wouldn't want to follow my method of madness anyway, but trust me just take your time and you'll be fine, it is really easy.

im gonna wait for a DIY i dont wanna be stuffin around too much
so someone do one.. ben .. im looking in your direction haha

Don't look at me guys, I didn't even buy a set of these! Im just the distributor.

aww ok. i still think you should do one . your so organised and stuff and have so much whoring expirience on here ha ha

un if any one needs a hand fitting these i can give you hand for a small fee of course....... mmmmm beeeeeerrr

Still waiting on 2 peoples details:

ytq536 - need your real name
Rauny - need your real name

I put them in this afternoon - very easy guys, just get out there and give it a go!

Taking it VERY slowly, lots of breaks, took 4hrs.

Hey ben just curious what day did you send the dials to me?

Friday. So you should see 'em today or tomorrow.