FTO AUSTRALIA

I'll take one if the price is $100 or less

Yeah eventually you should sell them all off.
I'd be interested, but it has to be a reasonable price

I'll take one Ps rang them up about 1-2 weeks ago and they said they can only make them for a group of 7 or more, so I reckon even if we have 6 they'll say yes.

Shadowarrior and spetz are interested too as stated in the other thread aslong as the price is right...
http://ftoaustralia.com/v3/viewtopic.php?f=1&t=26203

I also stated that in the post above yours

f**k they must be so over c**nts ringing about the uas pipe.

silverGPX wrote:f**k they must be so over c**nts ringing about the uas pipe.

Would almost be as bad as when we get people ringing to ask "what session times do you have for all your movies" and "what movies are you showing? what are they about?" over where I work

Well tbh its their fault for advertising it on their website, I rang up to see if they had any in stock and they said they can only make them again in groups of 7 or more, they should write that on their website or something.

Agreed. If they are not selling the product anymore then remove it from their 'updated' website or be prepared to answer queries about the listed product.

Sent from my GT-N7000 using Tapatalk 2

silverGPX wrote:f**k they must be so over c**nts ringing about the uas pipe.

They should just make a batch of 10 and sell them off one by one

I suggest every god damned time this comes up, someone needs to grab an existing pipe & go to a friggen rubber manufacturer. There's more than 1 company in the whole of Sydney that could produce these and for a better price. Cut out the middle man!

John's (UAS) supplier will only do them in batches & he gets reamed on the price. Therefore, all of you get reamed even harder for a simple bit of rubber!

Someone take the initiative & run with it!

That is a good idea.
However I am not in Sydney (not even in Australia at the moment) and where to get a UAS pipe from to copy?

Bennoz wrote:I suggest every god damned time this comes up, someone needs to grab an existing pipe & go to a friggen rubber manufacturer. There's more than 1 company in the whole of Sydney that could produce these and for a better price. Cut out the middle man!

John's (UAS) supplier will only do them in batches & he gets reamed on the price. Therefore, all of you get reamed even harder for a simple bit of rubber!

Someone take the initiative & run with it!

Was literally going to do this when I was doing my intake..
Then Evoman sold me his UAS pipe.

Oh and people, no one use initiative please! It keeps our UAS pipes worth something

Bennoz wrote:I suggest every god damned time this comes up, someone needs to grab an existing pipe & go to a friggen rubber manufacturer. There's more than 1 company in the whole of Sydney that could produce these and for a better price. Cut out the middle man!

John's (UAS) supplier will only do them in batches & he gets reamed on the price. Therefore, all of you get reamed even harder for a simple bit of rubber!

Someone take the initiative & run with it!

VECTOSE

PHIL069 wrote:

Bennoz wrote:I suggest every god damned time this comes up, someone needs to grab an existing pipe & go to a friggen rubber manufacturer. There's more than 1 company in the whole of Sydney that could produce these and for a better price. Cut out the middle man!

John's (UAS) supplier will only do them in batches & he gets reamed on the price. Therefore, all of you get reamed even harder for a simple bit of rubber!

Someone take the initiative & run with it!

VECTOSE

I don't have a UAS pipe.....

*Runs out and installs stock pipe*

bass_twitch wrote: Oh and people, no one use initiative please! It keeps our UAS pipes worth something

yeah who would wanna help the club, greed all the way

I've even got one I can lend as the template...

I live in the Wetherill Park/ Smithfield Area so there's heaps of Plastic Manufacturers in the area, I'll ring up and see if I can get some information/quotes.

Bennoz if you don't mind can I borrow it next week sometime? I've got a week off Uni so I'll draw it up in Autocad or Solidworks so I'll have the blueprint which will be a lot easier to replicate later whenever someone is interested. I've also got a friend in Ingleburn who works with 6061 aluminium, so I'll see how much he'll charge to make them and I'll get a few other quotes.