All gone.

AMACHA · Post by **AMACHA** » Wed Oct 24, 2007 9:53 am

hey buddy can i grab the super power flow kit off you mate? so it pretti much comes with everything ill need to install it?so pretti much everything in this pic http://www.perfectrun.com.au/real_size_ ... loaded.htm
Also id like to grab the uas pipe off you as well mate does that come iwth everything i need to isntall it like the clamps and pretti much i wont nee to buy anything else to isntall it isthat correct?will it fit in my engine bay im not sure if my battery is bigger than the standard one here is a pic of my engine bay,

P.S. no big deal but do you still have the box for it by any chance? If its possible i can grab the uas pipe and hks filter off y ou and pay on t he first of of november (my funds enter my bank account on the wednesday). Can we say 200 for the lot including postage?

Delvance · Post by **Delvance** » Wed Oct 24, 2007 10:33 am

1 HKS super power flow kit to AMACHA!

This is EXACTLY what it will come with

The pod shell, the metal case that holds the filter down, screw that holds the metal case to the shell, 3 filters (1 triple layer, 2 dual layer), 4" metal tube adapter, 2 steel cable clamps, and you can have my dodgy heatshield that went with it if you want (hey it works

).

The picture shows a kit not for an fto and that kit has a few bits extra such as some bolts (which i can see is used for the air flow sensor on that particular car). My kit doesn't have those screws but you won't need it as you've got a gpx and there's no air flow meter, just the map sensor.

PM incoming.

Oh woops, forgot to say...sorry i don't have the box

Delvance · Post by **Delvance** » Wed Oct 24, 2007 10:41 am

$200 plus post is fine for the UAS pipe and HKS kit. The UAS pipe is direct fit and should fit in your engine. The battery clamp will slightly push against the pipe but i eventually fixed that by just shifting the battery over then using a cable tie to not let it slide to the left where the intake pipe was.

The UAS pipe is not direct fit though, as it has no fitting for the breather hose. You're going to need an oil catch tank or make a dodgy one yourself (which i did haha). The clamps off your stock intake pipe will then go onto the UAS pipe but i can supply one clamp for the throttle body.

akumi · Post by **akumi** » Wed Oct 24, 2007 2:13 pm

Hey Amacha! Showo me your setup for the UAS pipe once u've installed it. I'm located in Sth Melbourne, which suburb are you located?

AMACHA · Post by **AMACHA** » Wed Oct 24, 2007 4:09 pm

hey akumi yep no worries i wont be fitting for another couple of weeks i got uni exams atm so once t here done ill fit it asap im located in Thornbury thats near Northcote Fairfield about 10 min drive from RMIT Uni in the city.

akumi · Post by **akumi** » Wed Oct 24, 2007 4:12 pm

nice! i used 2 work in northcote

bonker · Post by **bonker** » Wed Oct 31, 2007 3:44 am

Do you still have the exhaust ?.

Post by **Supplanter** » Wed Oct 31, 2007 1:49 pm

akumi wrote:Hey Amacha! Showo me your setup for the UAS pipe once u've installed it. I'm located in Sth Melbourne, which suburb are you located?

I have the whole UAS intake and live and work in Bentleigh.
What times are you at Eplot, Akumi?

akumi · Post by **akumi** » Wed Oct 31, 2007 1:54 pm

hi supplanter, i work from 8.30am till 7pm everyday mon to fri, sat is 11am to 3pm, it'll be great to see you coz it's been a while

Delvance · Post by **Delvance** » Wed Oct 31, 2007 2:36 pm

bonker wrote:Do you still have the exhaust ?.

Sorry, car went into exhaust shop today and no one posted "i'll take it
" so i didn't get it removed.