EvoScan software

Storm · Post by **Storm** » Wed Apr 01, 2009 7:40 pm

Anybody have or know the best place to get the EvoScan software?

I bought the cable but obviously need to get the drivers for it

Cheers

Bill

FTEvolution · Post by **FTEvolution** » Thu Apr 02, 2009 7:33 am

It's made in NZ, by mmc.org members I believe. Get it from the source, http://www.limitless.co.nz/

Post by **aza013** » Thu Apr 02, 2009 6:08 pm

If you do a search you will find the info as it is on here some place, may be in the GB area.

Storm · Post by **Storm** » Thu Apr 02, 2009 7:16 pm

Thanks guys, I bought it last night but I cant get it to stay hooked up. It connects then drops the connection and re-connects.

Has anyone an idea of the settings I should be using to stop this happening?

Cheers,

Bill

FTEvolution · Post by **FTEvolution** » Thu Apr 02, 2009 7:19 pm

Probably data rate on your laptop having issues. Perhaps you should ask on the site for some assistance, their forum is fantastic

Post by **Bennoz** » Thu Apr 02, 2009 7:34 pm

Want to email you the version I've got? They keep sending me updates, but i think its the latest.

Storm · Post by **Storm** » Thu Apr 02, 2009 8:14 pm

Cheers Ben but I got some advice on baud rates and stuff from d_dan so I will try that tonight and see. I've got v2.5 so hopefully that will be it.

I didn't see a forum on their site so I will have a better looklater when I'm not meant to be working for a living

Bill

knowhopetattoo · Post by **knowhopetattoo** » Wed Apr 08, 2009 8:14 pm

Is there any Queensland members with this setup......I have a tiptronic problem that I'd like to try and sought out.....the N flashes when I do the the diagnostics check.

Storm · Post by **Storm** » Wed Apr 08, 2009 9:35 pm

knowhopetattoo wrote:Is there any Queensland members with this setup......I have a tiptronic problem that I'd like to try and sought out.....the N flashes when I do the the diagnostics check.

what do you mean by the N flashes? Does it give a code or just flash as you can read the gearboc ECU codes from it the same as the engine codes. You can also read the ABS codes in the same way.

Grease Monkey on the FTOOC site gives a run down of the gearbox and ABS codes for you if it helps.

Bill

Post by **Bennoz** » Thu Apr 09, 2009 7:44 am

I pinched it

http://www.ftoaustralia.com/modules.php ... ic&t=14667

knowhopetattoo · Post by **knowhopetattoo** » Thu Apr 09, 2009 11:06 am

Automatic transmission - Chassis manual section 23

With a flashing N lamp there are two possibilities of what it could be.

If it flashes at 1Hz, once a second, then it will be either,

Input speed sensor
Output speed sensor
Solenoid valve
Out of phase at shift points
A/T control relay system

Storm · Post by **Storm** » Thu Apr 09, 2009 7:42 pm

Bennoz wrote:I pinched it

http://www.ftoaustralia.com/modules.php ... ic&t=14667

When you get your donations from folk I expect payment for my copyright infringement

Post by **Bennoz** » Fri Apr 10, 2009 9:03 am

Storm wrote:
Bennoz wrote:I pinched it

http://www.ftoaustralia.com/modules.php ... ic&t=14667
When you get your donations from folk I expect payment for my copyright infringement

Sure you dont just want me to knock off your misses instead?

Storm · Post by **Storm** » Fri Apr 10, 2009 7:24 pm

Bennoz wrote:
Storm wrote:
Bennoz wrote:I pinched it

http://www.ftoaustralia.com/modules.php ... ic&t=14667
When you get your donations from folk I expect payment for my copyright infringement
Sure you dont just want me to knock off your misses instead?

If you could make it look like an accident...

Ah sh*t, she'll probably be in an accident now and this will be draged into court