Fuse Box / Relay Translations
Moderators: IMC, Club Staff
- Supplanter
- Forum Moderator
- Posts: 6417
- jedwabna poszewka promocja
- Joined: Tue Oct 22, 2002 5:00 pm
- Location: Arizona Bay
- Contact:
- brent88
- Mechanic
- Posts: 724
- Joined: Tue Feb 23, 2010 6:00 pm
- Location: bendigo, victoria, Australia
- Contact:
Re: Fuse Box Translations
THANK YOU!!!!!! This fuse box translation is a life saver. i my reverse lights wouldent work aswell as some of my dash lights, did continuity checks ripped all the centre console outta my car, all the trim where the wires from the tail lights came from and couldent get them working even ran my own seperate wire. obiously looked at fuses first but didnt take em out only checked with multimeter and for some reason the fuse didnt show up as broken. after doing everything i went for a drive and i was stuck in 2nd gear i thought i wrecked my auto tranny just lucky i thought ill just double check those fuses.
number 3 fuse on your diagram controlls heaps of stuff and its only a 10amp reverse lights and the all important speed sensor so i guess the transmission couldent realise that i wanted next gear..... thought it woulda got stuck in first. also tip mode didnt work wich was odd. anyway great post a+!!!!!
number 3 fuse on your diagram controlls heaps of stuff and its only a 10amp reverse lights and the all important speed sensor so i guess the transmission couldent realise that i wanted next gear..... thought it woulda got stuck in first. also tip mode didnt work wich was odd. anyway great post a+!!!!!
-
- Newbie
- Posts: 10
- Joined: Tue Mar 15, 2011 5:55 pm
Re: Fuse Box Translations
Absolute legend!
I was messing around with my fto installing a new sound system when i blew some fuses and i couldnt work out which ones due to the Japanese writing lol.
Would anyone be able to narrow this one problem down for me?
Interior lights are obviously listed for the fuse but my central locking has stopped working also and worst of all the car keeps resetting when i turn it off.
If anyone has any suggestions it would be greatly appreciated.
Thanks
Simon.
I was messing around with my fto installing a new sound system when i blew some fuses and i couldnt work out which ones due to the Japanese writing lol.
Would anyone be able to narrow this one problem down for me?
Interior lights are obviously listed for the fuse but my central locking has stopped working also and worst of all the car keeps resetting when i turn it off.
If anyone has any suggestions it would be greatly appreciated.
Thanks
Simon.
- vipfto
- Forum Moderator
- Posts: 4154
- Joined: Mon Oct 29, 2007 5:00 pm
- Location: Adelaide
Re: Fuse Box Translations
no 4 will keep blowing and cause car to reset every time (10amp fuse)
If it keeps blowing you will have short and most likely would have wired head unit neg to indicator earth very easily done I always create new earth when doing head units or for any stereo install
If it keeps blowing you will have short and most likely would have wired head unit neg to indicator earth very easily done I always create new earth when doing head units or for any stereo install
FTO GR-TURBO
172KW ATW @ 11PSI
172KW ATW @ 11PSI
- Kustom
- Oldtimer
- Posts: 6144
- Joined: Sun Oct 04, 2009 5:00 pm
- Location: Brisbane
Re: Fuse Box Translations
Id check number 5 in the engine bay fuse box, that was causing me the same problems as you (even though un-related to stereo lol)
Taz wrote:When funds allow
- Taiwo
- Mechanic
- Posts: 463
- Joined: Sun May 15, 2011 6:53 pm
- Location: Brisbane, Wakerley
Re: Fuse Box Translations
this was very helpful. i found out 3 is what is wrong with my car. mainly the input and output sensor
- spetz
- Oldtimer
- Posts: 2915
- Joined: Wed Mar 03, 2004 6:00 pm
Re: Fuse Box Translations
Great stuff
-
- Newbie
- Posts: 16
- Joined: Wed Jun 01, 2011 2:55 pm
- Location: Sydney
Re: Fuse Box Translations
First of all, great post! Thanks Supplanter!
So both of my reverse lights ain't working and I checked them today, both the bulbs seem absolutely fine! My next guess would be the fuse? If thats the case, I just gotta replace a new 10A fuse on number 3 in first diagram??? (NT-ECU, AIT indicator lamp, Output/Input blah blah blah...)
So both of my reverse lights ain't working and I checked them today, both the bulbs seem absolutely fine! My next guess would be the fuse? If thats the case, I just gotta replace a new 10A fuse on number 3 in first diagram??? (NT-ECU, AIT indicator lamp, Output/Input blah blah blah...)
- PHIL069
- Oldtimer
- Posts: 4719
- Joined: Sun Sep 20, 2009 5:00 pm
- Location: Central Coast > South Australia
Re: Fuse Box Translations
Change the number 3 fuse first.Aqua wrote:First of all, great post! Thanks Supplanter!
So both of my reverse lights ain't working and I checked them today, both the bulbs seem absolutely fine! My next guess would be the fuse? If thats the case, I just gotta replace a new 10A fuse on number 3 in first diagram??? (NT-ECU, AIT indicator lamp, Output/Input blah blah blah...)
If that doesn't fix it, then.........
Check you have power at the globe terminals when the FTO is in reverse and ignition switch to on.
As it could also be your wiring or reverse light switch on your gearbox/transmission.
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done!
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now...
-
- Newbie
- Posts: 16
- Joined: Wed Jun 01, 2011 2:55 pm
- Location: Sydney
Re: Fuse Box Translations
Yeah I will try replace it first in the following week and see how it goes!
Thanks PHIL!
Thanks PHIL!
-
- Newbie
- Posts: 16
- Joined: Wed Jun 01, 2011 2:55 pm
- Location: Sydney
Re: Fuse Box Translations
Ok... so I just replaced the number 3 fuse with new 10A fuse and the reverse lights still ain't working
"...Check you have power at the globe terminals when the FTO is in reverse and ignition switch to on.
As it could also be your wiring or reverse light switch on your gearbox/transmission."
May you please give me more details on how to check the power at the globe terminals...?
Thanks!
"...Check you have power at the globe terminals when the FTO is in reverse and ignition switch to on.
As it could also be your wiring or reverse light switch on your gearbox/transmission."
May you please give me more details on how to check the power at the globe terminals...?
Thanks!
- ZFL45H1
- Oldtimer
- Posts: 1830
- Joined: Sun Feb 07, 2010 6:00 pm
- Location: Albury
Re: Fuse Box Translations
this is what happened to me recently change my switch and all is working its the same switch as a hyundai exel I found out only about $30PHIL069 wrote: As it could also be your wiring or reverse light switch on your gearbox/transmission.
gotta get there one day :)
- PHIL069
- Oldtimer
- Posts: 4719
- Joined: Sun Sep 20, 2009 5:00 pm
- Location: Central Coast > South Australia
Re: Fuse Box Translations
Touch each terminal of a test light or multi meter onto each of the globe terminals, test light should glow or 12V should show on multi meter.Aqua wrote:Ok... so I just replaced the number 3 fuse with new 10A fuse and the reverse lights still ain't working
"...Check you have power at the globe terminals when the FTO is in reverse and ignition switch to on.
As it could also be your wiring or reverse light switch on your gearbox/transmission."
May you please give me more details on how to check the power at the globe terminals...?
Thanks!
As ZFL45H1 said it is more than likely your switch, which is located on the top of the gearbox.
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done!
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now...
- Vectose
- Forum Moderator
- Posts: 3948
- Joined: Sun Nov 28, 2010 8:45 pm
- Location: Newcastle
Re: Fuse Box Translations
Before you buy a new switch, I would recommend taking it out and giving it a good clean with some throttle body cleaner or something similar. My reverse lights were not working before, so I removed the switch, gave it a good clean and they started working.
Bennoz wrote:A whoooole lot 'o jismTechnikhaus wrote:What is in said Bens big penis by the way?
-
- Newbie
- Posts: 16
- Joined: Wed Jun 01, 2011 2:55 pm
- Location: Sydney
Re: Fuse Box Translations
Thanks for all the support guys!
I will try removing it (hopefully its easy? coz I've never done it before...) and cleaning it first...
I will try removing it (hopefully its easy? coz I've never done it before...) and cleaning it first...
- ZFL45H1
- Oldtimer
- Posts: 1830
- Joined: Sun Feb 07, 2010 6:00 pm
- Location: Albury
Re: Fuse Box Translations
It is pretty easy just remove your air intake pipe and u sure pretty much be staring at it u just need a 22mm deep socket or around that size other then that it's easy good luck let us know how u go:DAqua wrote:Thanks for all the support guys!
I will try removing it (hopefully its easy? coz I've never done it before...) and cleaning it first...
gotta get there one day :)
- bass_twitch
- Oldtimer
- Posts: 2423
- Joined: Thu May 27, 2010 3:37 pm
- Location: Western Sydney, NSW
Re: Fuse Box Translations
Reminds me, I need to do mine.ZFL45H1 wrote:It is pretty easy just remove your air intake pipe and you sure pretty much be staring at it you just need a 22mm deep socket or around that size other then that it's easy good luck let us know how you go:DAqua wrote:Thanks for all the support guys!
I will try removing it (hopefully its easy? coz I've never done it before...) and cleaning it first...
Anyone got pictures of it?
- PHIL069
- Oldtimer
- Posts: 4719
- Joined: Sun Sep 20, 2009 5:00 pm
- Location: Central Coast > South Australia
Re: Fuse Box Translations
A picture courtesy of mikeey01nzl
I hope I have pointed it out clear enough
I hope I have pointed it out clear enough
mikeey01nzl wrote:Hats off to you too Phil for spending so much time on the phone trying to help someone out, your a top man and only a few would've spent so much time. well done!
Daniel2019 wrote:Come on phil, we bonded at the bonfire, lets be honest here...me and phil are besties now...
- bass_twitch
- Oldtimer
- Posts: 2423
- Joined: Thu May 27, 2010 3:37 pm
- Location: Western Sydney, NSW
Re: Fuse Box Translations
Can't see itPHIL069 wrote:A picture courtesy of mikeey01nzl
I hope I have pointed it out clear enough
Cool,
Thanks Phil
I'll do it eventually. Might check the no. 3 fuse first, just in case.
-
- Newbie
- Posts: 16
- Joined: Wed Jun 01, 2011 2:55 pm
- Location: Sydney
Re: Fuse Box Translations
Good news guys! turn out the switch was disconnected! so i just plugged it back in and the reverse lights work now!
Thanks for the support and suggestion everyone!
Thanks for the support and suggestion everyone!