FTO AUSTRALIA

Posted: **Thu Feb 19, 2009 7:43 pm**

shes back from the shop. Sorry about the crap pics my camera develop a fault so i had to use my phone

<a href="http://s50.photobucket.com/albums/f303/ ... G_0331.jpg" target="_blank"><img src="http://i50.photobucket.com/albums/f303/ ... G_0331.jpg" border="0" alt="Photobucket"></a>

<a href="http://s50.photobucket.com/albums/f303/ ... G_0327.jpg" target="_blank"><img src="http://i50.photobucket.com/albums/f303/ ... G_0327.jpg" border="0" alt="Photobucket"></a>
a href="http://s50.photobucket.com/albums/f303/ ... G_0329.jpg" target="_blank"><img src="http://i50.photobucket.com/albums/f303/ ... G_0329.jpg" border="0" alt="Photobucket"></a>

Posted: **Thu Feb 19, 2009 8:04 pm**

looks good. Are you happy with it

Posted: **Thu Feb 19, 2009 8:14 pm**

well yes and no. im happy with the welds and he did good quality mandible bends but the muffler is on a bit of an angle and slightly off center and I wanted the tips poking out more

Posted: **Thu Feb 19, 2009 8:38 pm**

Get them to re-adjust it. Theyll generally do that if you push a bit

Posted: **Thu Feb 19, 2009 10:54 pm**

looks hot ^^ love it..want to get mine done too

Posted: **Thu Feb 19, 2009 11:27 pm**

Here's a vid of my Varex in action, Grrrrr....
http://www.youtube.com/watch?v=ZZm4Z4XOMQs

Posted: **Thu Feb 19, 2009 11:32 pm**

omg i want i want so bad i am so changing my exhaust. when i ge my 3 inch done i am so geting one

Posted: **Fri Feb 20, 2009 2:58 am**

hey can you like draw the layout of the way the exhaust goes. How much was the muffler

Posted: **Fri Feb 20, 2009 9:03 am**

its the same as the ebay one on page one except its not dodgy

the muffler was $400

Posted: **Fri Feb 20, 2009 10:54 am**

ok kool so when they cut off the 2 3 inch tips off the vortex muffler. Did they use 3 inch piping to the tips as when I gt it done I am just going to have 2 tips 1 each side. Feel like frieghting one up here if they are cheaper down their plus freight.

Posted: **Fri Feb 20, 2009 11:09 am**

DAYUMMMM

Posted: **Fri Feb 20, 2009 11:11 am**

no thay ddn't, witch annoyed me a bit as I was under the impiession thay would use 3'' s-steel he even showed me the pipe he was going to use

Posted: **Fri Feb 20, 2009 11:52 am**

mmm maybe it didn't fit so he had to use 2.5. How does the car sound driving at 7400rpm does it tin at all or nice and deep.

Posted: **Fri Feb 20, 2009 11:59 am**

Well, I can say mine is nice and deep at that RPM

Posted: **Fri Feb 20, 2009 12:09 pm**

I haven't driven it with its loud setting yet as it isn't permanently wired up yet. it doesn't tin out on the quiet setting though.

Posted: **Fri Feb 20, 2009 2:35 pm**

ok mine does haha maybe because I have burnt my cat converter out haha. I have 2 cannons 1 on either side. But I have changed exhaust
3 times and always done it. I don't care change exhaust with new motor.

Posted: **Sat Feb 21, 2009 12:00 pm**

i just got off the phone with the guy from Brisbeane Exhaust center and he was happy to re-adjust the system for me. its nice I didn't to have to fight it. The system sound good and doesn't tin out at hi RPM but it makes a nasty sound when the engeine is loaded up at low rpm like if I take off from 2nd gear so I will ask him about fixing/tuning that when i take it in next week

Posted: **Sat Feb 21, 2009 12:06 pm**

ok that is good how is the exhaust wired up of you know. I am going in on monday to ask how much they are up here in darrwin

Posted: **Sat Feb 21, 2009 12:29 pm**

Its pretty straigh foward a little box goes in the front off the car and a wire goes to the muffler I put mine through the drain hole under the spare tyre then ran it above the muffler heat sheild. I had to cut the connector to fit it through then join it agian.

Posted: **Sun Feb 22, 2009 10:10 pm**

THAT WAS AMAZZZZZIIIIIIINNNNNNGGGGGGGGGGGGGGG....

i want i want i want.

i'd love to hear that in real life!

FTO AUSTRALIA

i'm getting twins