Page 1 of 2
Grill Mesh
Posted: Mon Oct 27, 2008 8:21 pm
by FknTopOne
Thought this would be easier to track down than it actually is.
I've seen a few pre-cut products in a few auto shops, but they don't have the right dimensions, I'm fitting it to a Bozz bar. Plus they're really over priced.
I've tried Bunnings but apparently no go for by the metre.
Any other ideas?
Re: Grill Mesh
Posted: Mon Oct 27, 2008 8:52 pm
by rock_it
FknTopOne wrote:Thought this would be easier to track down than it actually is.
I've seen a few pre-cut products in a few auto shops, but they don't have the right dimensions, I'm fitting it to a Bozz bar. Plus they're really over priced.
I've tried Bunnings but apparently no go for by the metre.
Any other ideas?
Go see the guys at Meek.com.au ... They had a flood load of mesh in a huge roll that they used on my Evo III bar ...
Posted: Mon Oct 27, 2008 9:11 pm
by I8A4RE
I have bozz and got the stuff i used to use from super cheap $30. I even had heaps extra to use for other things
Posted: Mon Oct 27, 2008 9:32 pm
by oodLes
I8A4RE wrote:I have bozz and got the stuff i used to use from super cheap $30. I even had heaps extra to use for other things
See you say that but the only stuff I could find in my area was way too small, I eventually found something from Repco but nowhere else had anything big enough.
Posted: Mon Oct 27, 2008 9:36 pm
by I8A4RE
well all the super cheap's are connected, so you could of ordered it in. If i reme,ber correctly i even offered to send you some down
Posted: Mon Oct 27, 2008 11:19 pm
by FknTopOne
Yeah Repco had the closest match yet.
The Supercheap store is right next door to my local Repco. They said they didn't sell it which is obviously BS.
I did not get a chance to get proper dimensions, and the bar is at the panel shop.
I got the dude there to measure up, he reckons about about 1100mm (L) x 500mm (w). Doesn't sound quite right to me.
Posted: Mon Oct 27, 2008 11:53 pm
by Supplanter
FknTopOne wrote:I got the dude there to measure up, he reckons about about 1100mm (L) x 500mm (w). Doesn't sound quite right to me.
11M by 5M... doesn't sound right at all
Posted: Tue Oct 28, 2008 12:44 am
by howc
i think its 1.1m by 0.5 m
Posted: Tue Oct 28, 2008 8:32 am
by I8A4RE
Supplanter wrote:FknTopOne wrote:I got the dude there to measure up, he reckons about about 1100mm (L) x 500mm (w). Doesn't sound quite right to me.
11M by 5M... doesn't sound right at all
ummm maybe its time to go back to school
Posted: Tue Oct 28, 2008 1:21 pm
by FknTopOne
ha ha
at 11m x 5m I could punch out all the windows and mesh them up as well.
But seriously is 1.5m x .5m right?
'cause I still can't find a match.
Posted: Tue Oct 28, 2008 1:58 pm
by I8A4RE
IF i remember ill measure mine tonight
Posted: Tue Oct 28, 2008 4:57 pm
by Tippin
I8A4RE wrote:IF i remember ill measure mine tonight
i remember seeing that your grill was white, did u get it like that or got it sprayed?
Posted: Tue Oct 28, 2008 6:16 pm
by I8A4RE
No it was stainless so that was probably just the flash making it look white
Posted: Tue Oct 28, 2008 6:27 pm
by I8A4RE
Well i dont know where he got his measurements from
Your hole at the widest points are
810mm x 265mm
So your mesh will need to be bigger than that by about 30mm or so all way the round
Posted: Tue Oct 28, 2008 7:41 pm
by FknTopOne
Thanks Simon
Now everyone knows the size of my hole
Yeah the panel dude prob just pulled those measurements out of his hole.
That make's life a lot easier.
I've seen a few products around that size.
Cheers
Posted: Tue Oct 28, 2008 7:54 pm
by I8A4RE
FknTopOne wrote:Thanks Simon
Now everyone knows the size of my hole
Yeah the panel dude prob just pulled those measurements out of his hole.
That make's life a lot easier.
I've seen a few products around that size.
Cheers
happy to help, i wish i could of filled your hole for you.............what
Posted: Tue Oct 28, 2008 8:53 pm
by FknTopOne
I8A4RE wrote:FknTopOne wrote:Thanks Simon
Now everyone knows the size of my hole
Yeah the panel dude prob just pulled those measurements out of his hole.
That make's life a lot easier.
I've seen a few products around that size.
Cheers
happy to help, i wish i could of filled your hole for you.............what
Goosh!
Glad my hole will have a steal mesh layer over it by tomoz.
Enuff said.
Posted: Wed Oct 29, 2008 1:49 pm
by harry90
FknTopOne wrote:I8A4RE wrote:FknTopOne wrote:Thanks Simon
Now everyone knows the size of my hole
Yeah the panel dude prob just pulled those measurements out of his hole.
That make's life a lot easier.
I've seen a few products around that size.
Cheers
happy to help, i wish i could of filled your hole for you.............what
Goosh!
Glad my hole will have a steal mesh layer over it by tomoz.
Enuff said.
BAHAHAHAH
Posted: Wed Oct 29, 2008 2:08 pm
by Supplanter
FknTopOne wrote:I8A4RE wrote:FknTopOne wrote:Thanks Simon
Now everyone knows the size of my hole
Yeah the panel dude prob just pulled those measurements out of his hole.
That make's life a lot easier.
I've seen a few products around that size.
Cheers
happy to help, i wish i could of filled your hole for you.............what
Goosh!
Glad my hole will have a steal mesh layer over it by tomoz.
Enuff said.
As long as you don't go to QLD you will be fine
Posted: Wed Oct 29, 2008 4:26 pm
by J
Supplanter wrote:FknTopOne wrote:I8A4RE wrote:FknTopOne wrote:Thanks Simon
Now everyone knows the size of my hole
Yeah the panel dude prob just pulled those measurements out of his hole.
That make's life a lot easier.
I've seen a few products around that size.
Cheers
happy to help, i wish i could of filled your hole for you.............what
Goosh!
Glad my hole will have a steal mesh layer over it by tomoz.
Enuff said.
As long as you don't go to QLD you will be fine
it wont matter what hole your talking about, in qld they'll fill it