Grill Mesh

FknTopOne · Post by **FknTopOne** » Mon Oct 27, 2008 8:21 pm

Thought this would be easier to track down than it actually is.
I've seen a few pre-cut products in a few auto shops, but they don't have the right dimensions, I'm fitting it to a Bozz bar. Plus they're really over priced.
I've tried Bunnings but apparently no go for by the metre.
Any other ideas?

rock_it · Post by **rock_it** » Mon Oct 27, 2008 8:52 pm

FknTopOne wrote:Thought this would be easier to track down than it actually is.
I've seen a few pre-cut products in a few auto shops, but they don't have the right dimensions, I'm fitting it to a Bozz bar. Plus they're really over priced.
I've tried Bunnings but apparently no go for by the metre.
Any other ideas?

Go see the guys at Meek.com.au ... They had a flood load of mesh in a huge roll that they used on my Evo III bar ...

Post by **I8A4RE** » Mon Oct 27, 2008 9:11 pm

I have bozz and got the stuff i used to use from super cheap $30. I even had heaps extra to use for other things

oodLes · Post by **oodLes** » Mon Oct 27, 2008 9:32 pm

I8A4RE wrote:I have bozz and got the stuff i used to use from super cheap $30. I even had heaps extra to use for other things

See you say that but the only stuff I could find in my area was way too small, I eventually found something from Repco but nowhere else had anything big enough.

Post by **I8A4RE** » Mon Oct 27, 2008 9:36 pm

well all the super cheap's are connected, so you could of ordered it in. If i reme,ber correctly i even offered to send you some down

FknTopOne · Post by **FknTopOne** » Mon Oct 27, 2008 11:19 pm

Yeah Repco had the closest match yet.
The Supercheap store is right next door to my local Repco. They said they didn't sell it which is obviously BS.
I did not get a chance to get proper dimensions, and the bar is at the panel shop.
I got the dude there to measure up, he reckons about about 1100mm (L) x 500mm (w). Doesn't sound quite right to me.

Post by **Supplanter** » Mon Oct 27, 2008 11:53 pm

FknTopOne wrote:I got the dude there to measure up, he reckons about about 1100mm (L) x 500mm (w). Doesn't sound quite right to me.

11M by 5M... doesn't sound right at all

howc · Post by **howc** » Tue Oct 28, 2008 12:44 am

i think its 1.1m by 0.5 m

Post by **I8A4RE** » Tue Oct 28, 2008 8:32 am

Supplanter wrote:
FknTopOne wrote:I got the dude there to measure up, he reckons about about 1100mm (L) x 500mm (w). Doesn't sound quite right to me.
11M by 5M... doesn't sound right at all

ummm maybe its time to go back to school

FknTopOne · Post by **FknTopOne** » Tue Oct 28, 2008 1:21 pm

ha ha

at 11m x 5m I could punch out all the windows and mesh them up as well.

But seriously is 1.5m x .5m right?

'cause I still can't find a match.

Post by **I8A4RE** » Tue Oct 28, 2008 1:58 pm

IF i remember ill measure mine tonight

Tippin · Post by **Tippin** » Tue Oct 28, 2008 4:57 pm

I8A4RE wrote:IF i remember ill measure mine tonight

i remember seeing that your grill was white, did u get it like that or got it sprayed?

Post by **I8A4RE** » Tue Oct 28, 2008 6:16 pm

No it was stainless so that was probably just the flash making it look white

Post by **I8A4RE** » Tue Oct 28, 2008 6:27 pm

Well i dont know where he got his measurements from

Your hole at the widest points are
810mm x 265mm

So your mesh will need to be bigger than that by about 30mm or so all way the round

FknTopOne · Post by **FknTopOne** » Tue Oct 28, 2008 7:41 pm

Thanks Simon

Now everyone knows the size of my hole

Yeah the panel dude prob just pulled those measurements out of his hole.

That make's life a lot easier.

I've seen a few products around that size.

Cheers

Post by **I8A4RE** » Tue Oct 28, 2008 7:54 pm

FknTopOne wrote:Thanks Simon

Now everyone knows the size of my hole

Yeah the panel dude prob just pulled those measurements out of his hole.

That make's life a lot easier.

I've seen a few products around that size.

Cheers

happy to help, i wish i could of filled your hole for you.............what

FknTopOne · Post by **FknTopOne** » Tue Oct 28, 2008 8:53 pm

I8A4RE wrote:
FknTopOne wrote:Thanks Simon

Now everyone knows the size of my hole

Yeah the panel dude prob just pulled those measurements out of his hole.

That make's life a lot easier.

I've seen a few products around that size.

Cheers
happy to help, i wish i could of filled your hole for you.............what

Goosh!

Glad my hole will have a steal mesh layer over it by tomoz.

Enuff said.

harry90 · Post by **harry90** » Wed Oct 29, 2008 1:49 pm

FknTopOne wrote:
I8A4RE wrote:
FknTopOne wrote:Thanks Simon

Now everyone knows the size of my hole

Yeah the panel dude prob just pulled those measurements out of his hole.

That make's life a lot easier.

I've seen a few products around that size.

Cheers
happy to help, i wish i could of filled your hole for you.............what
Goosh!

Glad my hole will have a steal mesh layer over it by tomoz.

Enuff said.

BAHAHAHAH

Post by **Supplanter** » Wed Oct 29, 2008 2:08 pm

FknTopOne wrote:
I8A4RE wrote:
FknTopOne wrote:Thanks Simon

Now everyone knows the size of my hole

Yeah the panel dude prob just pulled those measurements out of his hole.

That make's life a lot easier.

I've seen a few products around that size.

Cheers
happy to help, i wish i could of filled your hole for you.............what
Goosh!

Glad my hole will have a steal mesh layer over it by tomoz.

Enuff said.

As long as you don't go to QLD you will be fine

J · Post by J » Wed Oct 29, 2008 4:26 pm

Supplanter wrote:
FknTopOne wrote:
I8A4RE wrote:
FknTopOne wrote:Thanks Simon

Now everyone knows the size of my hole

Yeah the panel dude prob just pulled those measurements out of his hole.

That make's life a lot easier.

I've seen a few products around that size.

Cheers
happy to help, i wish i could of filled your hole for you.............what
Goosh!

Glad my hole will have a steal mesh layer over it by tomoz.

Enuff said.

As long as you don't go to QLD you will be fine

it wont matter what hole your talking about, in qld they'll fill it

FTO AUSTRALIA

Grill Mesh

Grill Mesh

Re: Grill Mesh