What work did you do on your car today?

[shadowarrior]

[destinationtoby]

Get that reciprocating saw out

I've been thinking of how it will help... But there's no way lol

[destinationtoby]

Going to have to borrow a fuckoff big drill and a metal drill bit

[Bennoz]

Run no spacers?

Then he'd have to buy rims with the correct offset. Unheard of!

[Bennoz]

Yeah yeah I know, broke it.........


If I get the car to a mechanic? Would they have a drill strong enough to just drill the fucka out in 10 seconds? Or a tyre place?

I'd grind a slot in either side of the locknut, then get a big fuckoff flat screw driver with the hex shaft & lock a shifter on to it & twist.

[Sahin]

Just go to the tire shop and say yeah just need a tire rotation mate

[bjk]

Just go to the tire shop and say yeah just need a tire rotation mate

Nek minnut $900 labour costs.

[destinationtoby]

Yeah yeah I know, broke it.........


If I get the car to a mechanic? Would they have a drill strong enough to just drill the fucka out in 10 seconds? Or a tyre place?

I'd grind a slot in either side of the locknut, then get a big fuckoff flat screw driver with the hex shaft & lock a shifter on to it & twist.

Tried it..

My wheels have a perfect offset Was just just trial fitting the spacers, didnt even get the second one on the car. And don't plan on it

[dstocks]

Yep, as Bennoz said. cut 2 narrow slots at 180 degrees with an angle grinder. You need something metal that fits in the slots and spans both of them (a flat piece of metal 3cm wide and about 3mm thick would be about the size you are looking for). Use a shifter on that and it should come off OK.

Put some work in on my custom bonnet in the last couple of days

[Daniel2019]

How did you do that? Can you write up a DIY please.

[dstocks]

ow did you do that? Can you write up a DIY please.

Who and what are you referring to?

[Daniel2019]

ow did you do that? Can you write up a DIY please.

Who and what are you referring to?

Toby.. just being a smartass

But in seriousness can you bash a socket on? Also +1 on cutting slots.

Similar principle to stabbing a screwdriver through a stuck oil filter, just more of a PITA.

[Cuoace]

Installed front strut brace new k&n Apollo cone air intake and cannon exhaust

[bjk]

That pipe almost looks long enough to go to the front bar! Might be interesting to try and fit it somewhere though.

[Bennoz]

Might be interesting to try and fit it somewhere though.

[shadowarrior]

I prefer the setup where I got this flexible pipe from ebay (same that Vectose has), that connects from the front of front bar grill, to the stock intake hole thingy on the body of the car where the stock airbox sat in.

[bjk]

Might be interesting to try and fit it somewhere though.

The shape is designed for maximum performance.

I prefer the setup where I got this flexible pipe from ebay (same that Vectose has), that connects from the front of front bar grill, to the stock intake hole thingy on the body of the car where the stock airbox sat in.

I have a couple of these waiting to put on too. Reckon I'll do the mesh for the non-foggies and polish headlights at the same time.

[destinationtoby]

But in seriousness can you bash a socket on? .

It's a circle

[Daniel2019]

1/4 or 1/2 inch drive extension or something on the inside? Vicegrips?

Just use the screwdriver suggestion

[destinationtoby]

I've tried it all man lol circle inside and out now. Nothing fits close enough to bash in. Even if I could there's not enough room because of the stud (reason for stripping it in the first place) nothing will go on the outside because there's 1mm clearance between the nut and the wheel. Can't grind slots any deeper without damaging the wheel.
Might just throw a Granada at it